Volume 12, Number 3 (2017)
CONTENTS
Effect
of Tooling Parameters on Bending Force in Air Bending of CR4 steel
pp. 375-388
Tilak Raj Gupta and H.S Payal
The Literature Review of Lean and Green
Manufacturing System
pp. 389-393
Vasdev Malhotra and Sameer Kumar
Relationship between Emotional
Intelligence and Job Performance of Software Professionals of Trivandrum
Technopark, Kerala, India
pp. 395-404
Sanjay B1 and Jubi R
Evolution of Microstructure and Hardness
of Aluminium 6061 after Friction Stir Welding
pp. 405-410
Ch.Mohana Raoa and K.Mallikarjuna Rao
The
Effect of Air Preheating on the performance and emission characteristics of a DI
Diesel Engine achieving HCCI mode of combustion
pp. 411-421
Sumanlal M. R., Sreeram Nandakumar and Mohanan P
Maintenance Challenges of Wankel Rotary
Engines and utility in Aviation Applications
pp. 423-434
K Subash, Vinu R and K Vijayaraja
Linearly Distributed Time Harmonic
Mechanical and Thermal Sources Effect at Transversely Isotropic Thermoelastic
Solids with Two Temperatures and without Energy Dissipation
pp. 435-443
Parveen Lata
Influence of Tool Geometry on Material
Flow Pattern in Friction Stir Welding Process
pp. 445-458
Pavan Kumar Thimmaraju, Krishnaiah Arakanti and G.Chandra Mohan Reddy
Transformation of Diesel Engine to Dual
Fuel Engine Using Injector Nozzle of Multi Holes Geometries: A review
pp. 459-472
Patel Nimit M and A.D.Patel
Effect
of Process Parameters on Metallurgical and Mechanical Properties of Friction
Stir Welded Aluminum Alloys
pp. 473-484
M.S. Srinivasa Rao, B.V.R. Ravi Kumar and M. Manzoor Hussain
Design of Ionofree Micro Strip Quad Helix
Antenna for Global Positioning System
pp. 485-495
Jesavath Kiran Naik¹ and S Muruganand
Effect of Aspect Ratio on the Performance
of Hydrodynamic Journal Bearing Operating Under Wear
pp. 497-522
Sanjay Sharma and R K Awasthi
Optimisation of 16cm2 Single Pass
Serpentine Flow Channel of PEMFC Using Taguchi Method
pp. 523-532
V. Lakshminarayanan and Bala Karthick K.S
Numerical Analysis of Soil-Water Flow in Fixed Horizontal Pipe
pp. 533-541
ManjitSingha, Sandeep Jindala, Amit Guptaa and Virender Chahal
Agriculture Productivity Enhancement
System using IOT
pp. 543-554
T.Satish, T. Bhavani and Shameena Begum
Thermodynamic (Energy-exergy) Analysis of
Hydrogen Liquefaction System
pp. 555-561
Devender Kumar and R.S Mishra
Thermodynamic (Exergy-energy) Analysis of
a Low Pressure Improved Claude Cycle Using Control Volume Technique For
Liquefaction of Gases
pp. 563-570
Devender Kumar and R.S Mishra
Estimation of Soil Moisture Content: A
Review
pp. 571-577
Saima Ansari and Ratnadeep R. Deshmukh
Effect of Change in Process Parameters on
Energy Consumption during Textile Dyeing Process
pp. 579-588
Kuldip Arun Rade, Vilas A. Pharande and Daulat. R. Saini
Sliding Mode Control of MERS for
Brightness Control of Discharge Lamps with Unity Power Factor
pp. 589-597
M.Vijayasanthi and M. Sushama
Effect of Porous Medium on
Thermo-Hydraulic Performance of Micro Channel Heat Sink
pp. 599-612
Saravanan Va and C. K. Umesh
Thermal
Performance Analysis to Assess Inhabitant Comfort inside LIG houses in
Chhattisgarh
pp. 613-622
Nisha Netam, Shubhashis Sanyal and Shubhankar Bhowmick
Generation of Manipulability Ellipsoids
for Different Configurations Using the Yoshikawa’s Manipulability Index and
Manipulability Ellipsoid
pp. 623-635
A. Chandrashekhar and Garlanka Satish Babu
Effect of Temperature and other factors
on Anaerobic Digestion Process, responsible for Bio Gas Production
pp. 637-657
Gurinderpal Singh, V.K. Jain and Amanpreet Singh
Corrosion Behaviour of Nickel Coated
Short Carbon Fiber Reinforced Al Metal Matrix Composites
pp. 659-669
Nithin Kumar, H. C. Chittappa, Ravikiran Kamath B and S. Ezhil Vannand
Corrosion Behaviour of Nickel Coated Short Carbon Fiber Reinforced Al Metal
Matrix Composites
pp. 659-669
Nithin Kumar, H. C. Chittappa, Ravikiran Kamath
and S. Ezhil Vannand
Analysis
of factors affecting the Lean and Green Manufacturing Systems by ISM approach
pp. 671-675
Dr. VasdevMalhotra and SameerKumar